7 Steps To Secure Your Linux Server

7 Steps To Secure Your Linux Server

This tutorial will introduce you to basic Linux server security. While it focuses on Debian/Ubuntu, you can apply everything presented here to other Linux distributions. I also encourage you to research this material and extend it where applicable.

1. Update your server

The first thing you should do to secure your server is to update the local repositories and upgrade the operating system and installed applications by applying the latest patches.

On Ubuntu and Debian:

$ sudo apt update && sudo apt upgrade -y

On Fedora, CentOS, or RHEL:

$ sudo dnf upgrade

2. Create a new privileged user account

Next, create a new user account. You should never log into your server as root. Instead, create your own account (“<user>“), give it sudo rights, and use it to log into your server.

Start out by creating a new user:

$ adduser <username>

Give your new user account sudo rights by appending (-a) the sudo group (-G) to the user’s group membership:

$ usermod -a -G sudo <username>

3. Upload your SSH key

You’ll want to use an SSH key to log into your new server. You can upload your pre-generated SSH key to your new server using the ssh-copy-id command:

$ ssh-copy-id <username>@ip_address

Now you can log into your new server without having to type in a password.

4. Secure SSH

Next, make these three changes:

  • Disable SSH password authentication
  • Restrict root from logging in remotely
  • Restrict access to IPv4 or IPv6

Open /etc/ssh/sshd_config using your text editor of choice and ensure these lines:

PasswordAuthentication yes
PermitRootLogin yes

look like this:

PasswordAuthentication no
PermitRootLogin no

Next, restrict the SSH service to either IPv4 or IPv6 by modifying the AddressFamily option. To change it to use only IPv4 (which should be fine for most folks) make this change:

AddressFamily inet

Restart the SSH service to enable your changes. Note that it’s a good idea to have two active connections to your server before restarting the SSH server. Having that extra connection allows you to fix anything should the restart go wrong.

On Ubuntu:

$ sudo service sshd restart

On Fedora or CentOS or anything using Systemd:

$ sudo systemctl restart sshd

5. Enable a firewall

Now you need to install a firewall, enable it, and configure it only to allow network traffic that you designate. Uncomplicated Firewall (UFW) is an easy-to-use interface to iptables that greatly simplifies the process of configuring a firewall.

You can install UFW with:

$ sudo apt install ufw

By default, UFW denies all incoming connections and allows all outgoing connections. This means any application on your server can reach the internet, but anything trying to reach your server cannot connect.

First, make sure you can log in by enabling access to SSH, HTTP, and HTTPS:

$ sudo ufw allow ssh
$ sudo ufw allow http
$ sudo ufw allow https

Then enable UFW:

$ sudo ufw enable

You can see what services are allowed and denied with:

$ sudo ufw status

If you ever want to disable UFW, you can do so by typing:

$ sudo ufw disable

You can also use firewall-cmd, which is already installed and integrated into some distributions.

6. Install Fail2ban

Fail2ban is an application that examines server logs looking for repeated or automated attacks. If any are found, it will alter the firewall to block the attacker’s IP address either permanently or for a specified amount of time.

You can install Fail2ban by typing:

$ sudo apt install fail2ban -y

Then copy the included configuration file:

$ sudo cp /etc/fail2ban/jail.conf /etc/fail2ban/jail.local

And restart Fail2ban:

$ sudo service fail2ban restart

That’s all there is to it. The software will continuously examine the log files looking for attacks. After a while, the app will build up quite a list of banned IP addresses. You can view this list by requesting the current status of the SSH service with:

$ sudo fail2ban-client status ssh

7. Remove unused network-facing services

Almost all Linux server operating systems come with a few network-facing services enabled. You’ll want to keep most of them. However, there are a few that you might want to remove. You can see all running network services by using the ss command:

$ sudo ss -atpu

The output from ss will differ depending on your operating system. This is an example of what you might see. It shows that the SSH (sshd) and Ngnix (nginx) services are listening and ready for connection:

tcp LISTEN 0 128 *:http *:* users:(("nginx",pid=22563,fd=7))
tcp LISTEN 0 128 *:ssh *:* users:(("sshd",pid=685,fd=3))

How you go about removing an unused service (“<service_name>“) will differ depending on your operating system and the package manager it uses.

To remove an unused service on Debian/Ubuntu:

$ sudo apt purge <service_name>

To remove an unused service on Red Hat/CentOS:

$ sudo yum remove <service_name>

Run ss -atup again to verify that the unused services are no longer installed and running.

We want to hear your thoughts about this.

About the Author
Web Guy
We have a burning desire to assist as many people as possible obtain a digital presence. We have and will keep striving to provide our clients with enterprise-level performance at an unbeatable cost. We are proud to offer a wide range of customized, hybrid, virtual private server (VPS) hosting and web development services. All our clients enjoy a 99.9% uptime SLA and 24/7 rapid response support team. We have a core directive to always provide our clients with the best services and infrastructure possible, no matter if you’re hosting a game server, a high-intensity database, a development environment, or anything in-between. Contact Us for more details.

Leave a Reply